Under Cabinet Lighting Placement: Front, Center, or Back?

Nov 16, 2026     By EZVALO Team

For food prep, start with the light near the front of the upper cabinet, close to the doors. To light the backsplash (the wall behind the counter), try a spot near the back. If you have a shiny counter, switch on the light and check for bright reflections before you attach it.


To test under cabinet lighting placement, hold the same light in three spots and see where it shines. Here’s what to look for at each spot.


In this guide: Where to place the light · How to test before mounting · How to install without wiring · Common questions

Where to place under cabinet lighting

Front, center, and back all mean spots on the bottom of the upper cabinet. The front is by the doors, the back is by the wall, and the center is halfway between them.

Light positionTry it whenCheck before mounting
Front, near the doorsYou chop, mix, or read recipes at the counter.Can you see your hands and cutting board clearly?
Center, halfway between doors and wallYou want some light on both the counter and the wall, or the front position causes glare.Is the front of the counter still bright enough to work at?
Back, near the backsplashYou want to show off the tile or light a coffee station against the wall.Is the area around the coffee maker or display lit where you need it?

Side view of three mounting positions. The door is on the left and the wall is on the right.

Juno Lighting’s application guide shows how the small ledge along the front of some cabinets can hide the light while it shines on the counter. If a shiny counter reflects the light into your eyes, KraftMaid’s kitchen lighting guide suggests aiming an adjustable light toward the backsplash from behind that front ledge. If your light can’t tilt, compare the front and center positions. If it dims, try turning it down a little.

Test the position before you mount the light

  1. Set up the counter the way you use it. Put a cutting board or coffee mug in its usual spot. Set the overhead lights as you normally would. If you use the kitchen after dark, repeat the check then.
  2. Compare three spots with the same light. Have someone hold the light under the cabinet at the front, center, and back. Keep the brightness and beam angle the same for each position. Stand where you normally work and move your hands over the board to see where the shadows fall.
  3. Look from across the room. Sit where you normally do, such as at the kitchen table. If you see bright dots or reflections, try moving the light slightly or tucking it behind the cabinet’s front ledge. Then check the cutting board again.
  4. Check the sensor and charging space. If the light turns on when it detects motion, walk into the kitchen the way you normally do and see if it comes on. Open the cabinet doors. Make sure you can still reach the controls and take the light down or plug it in to charge.

For example, a cutting board near the front of a counter and a coffee machine against the wall may need different placements. Start near the front above the board. At the coffee station, try a position farther back and check that you can still see the controls and the mug under the spout.

How to install under cabinet lighting without wiring

Use a rechargeable light bar or puck lights (small, round lights) that run on batteries. Once you’ve picked the spot, follow these steps:

  1. Check the mount. A magnetic light needs a surface the magnet sticks to or a metal mounting plate made for that light. If you’re using adhesive, check that it works with your cabinet finish.
  2. Clean and dry the spot. Do this before sticking down an adhesive mounting plate.
  3. Attach the mount and light. If the mount uses adhesive, follow the maker’s instructions for how firmly to press and how long to wait before attaching the light.
  4. Switch it on. Check that it lights the right area and that you can still remove it or reach the charging port.

If you’re comparing rechargeable under cabinet lights, the EZVALO EZL27 light bar is one option. Measure the flat space under your cabinet and check the mounting details before choosing a size.

Common questions

How far back from the front edge should the light go?

Start just behind the front lip if there’s room for the fixture and the lip doesn’t block the beam or sensor. Cabinet depth, trim, and fixture shape vary, so use the spot that lights your work surface and keeps the LEDs out of your normal line of sight.

Should I use one long bar or several puck lights?

Try a bar when you want light along a stretch of countertop. Puck lights can work for separate spots, such as a coffee station or a small display. If you use several pucks for prep, switch them all on and check for dark gaps between them. See EZVALO’s guide to under cabinet light types for more on the formats.

Can I use motion mode while I’m cooking?

Motion mode is handy when you walk into the kitchen. If you’re staying in one spot to read a recipe or prep food, try a steady mode if your model offers one. Test both modes at the chosen spot before mounting, since trim and nearby objects can affect what the sensor sees.

Start where you use the counter most: near the front for food prep or closer to the wall to highlight the backsplash. Once you know where the light will go and how much room you have, browse EZVALO under cabinet lights to compare fixtures that fit.